Order Bronze Cord

Use this guide to brief us on your Bronze Cord order, confirm the make-ready details and request samples first. For quotes, send the enquiry through the contact form.

A hot stamping press applies bronze foil to a card in an industrial workshop with foil rolls and sample cards.

What to include in your enquiry

When you order Bronze Cord, include the substrate, press type, roll width, roll length, quantity and the town where the work will run. If you are unsure about any of those points, send the job details you have and ask for guidance before final approval.

Useful details to add are the board or film type, whether the work is on leather, kraft board or wine cartons, and whether the job is being run on a platen, cylinder or roll to roll press. If you already have a die type or make-ready note, include that too.

  • Substrate and finish area
  • Press type and die material
  • Roll width needed after slitting
  • Approximate length and quantity
  • Town or delivery point

For a quick start, review the Bronze Cord specifications and Bronze Cord substrates before sending your enquiry.

Samples and swatches first

Before confirming a production roll, ask for swatches or samples so the colour, cord effect and release behaviour can be checked against the stock you are using. That is especially useful when the foil must sit neatly on coated board, soft-touch laminate or textured leather.

Test the sample on the actual substrate and under the same press conditions planned for the job. Check the finish in both good light and normal handling conditions so you can judge the antique depth and the edge detail properly.

If you are comparing more than one finish, keep the substrate and press settings the same and change only one factor at a time. That makes it easier to see whether the issue is with the foil, the die or the stock.

See the Bronze Cord press notes for make-ready guidance.

Press setup to check

Bronze Cord is typically started in a working range of about 130 to 145°C, with soft release and an antique bronze depth. Use that as a testing point only, then adjust for your stock, press speed and die condition.

During make-ready, check the temperature window, dwell, pressure and release profile before you run the full job. A stable impression depends on the substrate, the foil and the die all working together.

  • Temperature test within the stated starting range
  • Dwell allow enough time for clean transfer
  • Pressure match to the stock and die face
  • Release confirm a clean pull with no picking

For more substrate guidance, go back to the substrates before the final run.

how rolls are supplied

This foil family is supplied slit to the roll width you need, so the enquiry should state the finished width clearly. If you need more than one width, list each one separately to avoid confusion when the order is prepared.

Rolls are packed for trade handling and can be collected or sent by courier, depending on what you arrange through the order process. If your job is going direct to press, note the collection town and whether you need the rolls grouped by width or by job.

Keep the packaging note simple and practical. Mention if the rolls need to be labelled for a specific line, if there are multiple delivery points, or if the stock should be held for collection at the trade counter.

Order detailWhat to state
Finished widthExact slit width required
LengthApproximate roll length
HandlingCollection or courier
LabellingJob name or press line if needed

confirming your quote

Once the details are checked, your quote is confirmed in writing. Keep the enquiry clear, because the more complete the job brief is, the easier it is to confirm the correct foil, width and packing method without delays in back and forth.

Do not send a rough request if the job depends on exact appearance or press behaviour. Instead, ask for sample support first, then confirm the final specification after testing. That is the safest way to order when the finish must hold on leather goods, cartons, labels or soft-touch laminate.

For a direct enquiry, use the contact form. If you need to check the broader range, the products hub is the best place to start.

where bronze cord fits

Bronze Cord suits jobs where a warm bronze tone and a more antique appearance are needed on leather, kraft board and wine cartons. It can also be considered where the press setup is already tuned for a soft release and a controlled transfer.

The foil is used with suitable dies and a proper make-ready on platen, cylinder or roll to roll presses. For the best result, match the substrate to the correct foil family and confirm the transfer on the actual stock before production.

If you are planning a wider application, compare the finish with other foil families and related uses on the applications and finishes sections.

What our Hot Stamping Foil customers say

Verified Google reviews

Ask about a foil for your job

Send a note through our contact form with the substrate, the press you run (platen, cylinder or roll-to-roll), the finish you are after and the run length, and we will come back with a foil grade, a sample and a quote.

Open the contact form