Bank certificate run
A security-heavy foil job for bank certificates, set up for clean micro detail and covert markers. The run focused on registration, release control and reliable press make-ready.

Job brief
This run needed a restrained finish that would carry fine security detail without crowding the document. The brief called for a sharp foil mark on certificate stock, with covert markers built into the artwork and a clean edge that would read well under close inspection.
For this kind of work, the foil choice and die finish matter as much as the artwork. A crisp security foil was selected for the visible mark, while the hidden elements were set into the layout so they could sit inside the design rather than outside it.
- Fine line work for the certificate face
- Covert marker areas kept discreet in the artwork
- Clean release needed on coated board and secure paper stocks
For similar security work, see Pharma Tamper Seals and Museum Event Tickets.
Foil and die choice
The foil had to hold detail in small areas and release cleanly without filling in the micro elements. A security foil from the range was the right fit, with a finish that could carry the visible mark and the covert features at the same time.
The die choice was set around the detail in the artwork. For tight line work and small repeat features, a well-made brass or copper die can give the control needed on platen or cylinder work. The aim is always the same: even heat, clean impression and good release across the full image area.
| Item | Purpose |
|---|---|
| Security foil | Visible mark with covert detail |
| Brass or copper die | Fine line control and consistent transfer |
| Slit foil roll | Matched to press width and web format |
Foil swatch books and samples help confirm the look before the run. When needed, see the products range for metallic, pigment, holographic and specialty options.
Press setup
The setup work focused on temperature, dwell and pressure, with a starting point tested on the actual stock before the full run began. Security work does not reward guesswork. The foil must release at the right point, and the impression must be firm enough to transfer detail without marking the sheet too heavily.
Make-ready included careful alignment, a check on the die face, and a review of the release profile across the press area. On certificate work, small changes in stock coating or surface texture can alter the result, so the first pull is used to set the window rather than force it.
- Test the starting temperature window on the intended stock
- Check dwell and pressure in small steps
- Confirm release on the first printed sheets
- Adjust make-ready before going to full production
For related press-side guidance, visit Journal or the contact form.
Result on press
The run produced a clean security finish with the fine elements intact and the covert markers holding their place in the artwork. The foil sat neatly on the certificate surface, with good edge definition and no heavy build-up on the small details.
That kind of result depends on matching foil, die and press conditions to the substrate. On certificate jobs, the work often needs to hold up under close viewing, so the finish must stay sharp rather than decorative for its own sake. The final setting was chosen for consistent transfer across the sheet and stable output through the run.
If the stock changes, the press plan should be checked again. Coated papers, soft-touch laminate and other treated surfaces can all change release behaviour, so a new test is the sensible way to keep the result predictable.
Planning a similar run
Security certificate work, invitation suites, tickets and tamper labels all need a controlled foil process. The right foil family and the right die setup depend on the stock, the press type and the level of detail in the artwork.
Stampingfoil can supply security foils, slit rolls, samples and press-side advice for platen, cylinder and roll-to-roll presses. If you are planning a bank certificate, a secure label or another fine-detail job, use the contact form to ask for a quote and confirm the best test window for your stock.
What our Hot Stamping Foil customers say
Verified Google reviews
Also worth a look




Ask about a foil for your job
Send a note through our contact form with the substrate, the press you run (platen, cylinder or roll-to-roll), the finish you are after and the run length, and we will come back with a foil grade, a sample and a quote.
Open the contact form
