QA checklist

Use this checklist to confirm foil is packed, labelled and press-ready before it leaves Jet Park. It helps you catch issues early and reduce setup delays.

Man in a blue shirt measures a gold foil roll beside sample strips and foil spools on a workshop table.

What we check first

Before a trade delivery is released, the first check is simple: does the order match the request on type, colour, finish and roll width. We also confirm whether the foil is intended for coated board, soft-touch laminate, plastics, textiles or leather, because the application changes the setup on press.

For repeat work, compare the current roll against the previous approved sample book or master swatch. If the job depends on a specific metallic tone, holographic effect or security finish, that reference helps keep expectations clear before make-ready starts.

  • Confirm foil family, finish and colour name
  • Check roll width against the press and die layout
  • Match the foil to the intended substrate
  • Compare against the approved swatch or sample

If you need help matching a foil to a job, use the foil selection guide or request a sample through the contact form.

Roll and slit checks

Foil supplied slit to width should be checked for edge condition, roll winding and core fit. A neat roll helps with stable feeding on platen, cylinder and roll-to-roll presses. We also check that the roll length and slit width suit the planned run so the press team is not forced to improvise on the machine.

For narrow work on labels, or wider coverage on cartons and book covers, the slit width must suit the die area and the press format. A roll that is too wide can waste material. A roll that is too narrow can leave exposed areas or cause a second pass that should not have been needed.

Where required, we can pack swatch books and samples alongside the shipment so the finishing team can confirm the colour and effect at the bench before loading the press.

Press-ready details

The right foil still needs the right press settings. Before dispatch, note the intended press type and the likely starting window for testing, then share it with the operator. Typical starting ranges are only a guide and must always be tested on the actual stock, die and press.

Useful checks include temperature, dwell time, pressure, release profile and substrate response. On coated board, soft-touch laminate and some plastics, the first trial should confirm whether the foil releases cleanly and whether the image holds sharp edges. On leather and textured materials, the same foil may need a different balance of heat and pressure.

CheckWhat to confirm
TemperatureStart with a test range suited to the foil and substrate
DwellEnough time for transfer without overburning
PressureEven contact across the die face
ReleaseClean pull, with no patchy image or pick-off

For press-side guidance, see the press settings sheet.

Dies and make ready

Die condition is part of the quality check. Magnesium, copper and brass dies each behave differently, so the foil release and line sharpness need to be assessed with the actual tooling that will run the job. Before a trade delivery goes out, confirm that the die design, mounted area and image detail suit the selected foil.

Make-ready should also be considered. If the job includes fine type, foil tints, security detail or a full-bleed decorative effect, check that the press team has the right registration notes and enough sample material to test properly. A small setup change at this stage can save wasted stock later.

For die-specific notes, refer to die making notes and, if the finish is new to the job, the finishing glossary.

Packing and aftercare

Final dispatch checks are about protecting the foil in transit and keeping the finish usable when it arrives. Rolls should be packed to avoid crushing, heat exposure and contamination. Storage advice matters as much as packing, especially for foils that will sit before use.

When the delivery lands, keep rolls in a clean, dry area and avoid leaving them next to direct heat or sunlight. If the job is sensitive, the finishing team should open the pack only when ready to test and should keep the sample and roll identification together for traceability.

If a job needs more than one finish, compare the foil set before the press run starts. For security work, consult the security options overview. For storage and handling, see care and storage or ask for a quote through the contact form.

What our Hot Stamping Foil customers say

Verified Google reviews

Ask about a foil for your job

Send a note through our contact form with the substrate, the press you run (platen, cylinder or roll-to-roll), the finish you are after and the run length, and we will come back with a foil grade, a sample and a quote.

Open the contact form