Prism Holo

A diffraction foil with vivid movement and tamper-aware visual impact for short runs and repeat production. Use it where security detail and standout finish matter.

Hot stamping press beside holographic foil sheets, a foil roll, and beige cartons on a dark work surface.

What it is

Prism Holo is a rainbow holographic hot stamping foil with a clear diffraction sparkle and a strong visual cue for tamper awareness. It is used where the finish must do more than decorate, such as security seals, youth packaging and event tickets.

The effect changes with light and viewing angle, which makes it useful for brand features that need attention as well as a recognisable finish. For the broader foil family, see Product families.

It sits alongside other foil options such as metallics, pigments, security foils and specialty foils, but its main role is the rainbow holographic look. If you need a similar visual direction with another finish, compare it with Diffraction Beam or other product families listed on Products.

Where it suits

This foil is commonly used on applications that need a visible anti-tamper cue or a bright, modern finish.

  • Security seals and labels
  • Youth packaging
  • Event tickets and passes
  • Short-run branded components that need strong shelf or hand-held impact

It can be considered for coated board, paperboard, labels and certain laminate structures, depending on the surface and the die detail. If you are unsure about the stock, use the ordering and substrate pages before make-ready: substrates and ordering.

For work on coated cartons, soft-touch laminate or labels, check whether the area being stamped has enough surface integrity for clean transfer. When you need a foil made for another material family, look at PlasticBond, TextileSheen or LeatherMark.

Press setup

Typical starting points for trialing are 125 to 140°C, then adjust to the actual press, stock and die. Use these only as a test window, not as a guarantee, because release and transfer depend on the whole setup.

CheckWhat to look for
TemperatureStart in the test window and move in small steps until the image releases cleanly.
DwellEnough contact time for transfer without crushing detail or overworking the stock.
PressureEven, controlled pressure across the stamped area, especially on fine copy and patterned artwork.
Release profileClean release from the carrier with no patchy pull-back, over-transfer or dull patches.

Use the press notes before going on press: Press notes. The foil can be set up on platen, cylinder or roll-to-roll equipment, provided the die and make-ready match the job.

For detailed setup, ask for press-side advice through the contact form.

Dies and make-ready

Good results depend on matching the foil to the die and to the make-ready. Magnesium, copper and brass dies each behave differently, so line depth, area coverage and fine detail should be checked before production.

On harder stocks and coated surfaces, start with clean, level make-ready and confirm the die face is carrying pressure evenly. On softer or textured surfaces, keep an eye on impression depth so the stamp does not distort the sheet or block fine holographic detail.

If the artwork includes security cues, micro detail or dense patterning, test the smallest elements first. When a job needs a tighter setup plan, use the product notes and the family pages together, then move to Prism Holo Specifications for the finishing details.

For similar setup guidance on other foil families, see Security Micro or return to Product families.

Rolls and ordering

Prism Holo is supplied slit to roll width for the job at hand, with swatch books and samples available to help with matching and approval. Roll width should be confirmed against the press and the artwork before ordering.

Use the order link when you are ready to specify the foil, substrate and application details: Order Prism Holo. If you need help deciding between finishes, compare it with Aurum Gold, Argent Silver, Chrome Mirror or Bronze Cord.

For a wider finish selection or advice on another application, use the contact form.

What our Hot Stamping Foil customers say

Verified Google reviews

Ask about a foil for your job

Send a note through our contact form with the substrate, the press you run (platen, cylinder or roll-to-roll), the finish you are after and the run length, and we will come back with a foil grade, a sample and a quote.

Open the contact form